How to Install New Baseboard – Part 2


If you’re just joining us, make sure you START HERE to catch up on the first few steps of installing new baseboard. Yesterday we tackled steps #1 through #4 and today we are picking up where we left off to finish up this attainable DIY projectHow to Install Baseboard | DIY Playbook

If you’re back for more baseboard business, let’s dive right in. Here are the remaining steps (and lots of Rookie Tips!) to replace the baseboard in your home.

1. Buy New Baseboard & ShoeBuy Baseboard and shoe: How to Install Baseboard | DIY Playbook

You obviously need to buy new material (baseboard and shoe*) for this project. Chances are you’ll probably want to buy the same style baseboard that you have throughout the rest of your home so the new baseboard looks cohesive with the existing type.

Once you know the style, go ahead and buy the baseboard. But make sure you buy pieces that are LONGER than the wall you are attaching it to. This is important because you need toย have plenty of room to make your cuts on both ends and still have it fit onto the wall.

Align it properly: How to Install Baseboard | DIY Playbook*The shoe of the baseboard is that bottom piece that juts out a little bit and is connected to the floor. Believe it or not, this is a separate piece of wood that is attached to the baseboard after it’s attached to the wall. Whatever length you buy of the baseboard, you’ll need to buy the same length for the shoe.ย 

2. Measure & Cut Miters on the Baseboards

Once you have the material all set, it’s time to cut both the baseboard and the shoe to size.

Here’s where yourย miter saw is needed. I usually cut the new baseboard exactly how the old pieces were cut. If the old baseboard butts up to a straight edge (like a vent) than you will probably cut it straight, which makes the cutting process a whole lot easier.

However, if you’re meeting two corners of wood then you’ll most likely be “mitering” the corners, which means cutting each at a 45 degree angle. This is necessary so that when they are matched up together they make a perfect 90 degree angle at the corner. You can see in the photo above that you make these cuts by simply moving the saw blade from 0 degrees to 45 degrees. You cut it the exact same way, it’s just the saw itself that is reconfigured so that corners will be mitered.

Make clean cuts: How to Install Baseboard | DIY PlaybookThis baseboard was cut at a 45 degreeย and notice that it was cut standing straight up on the saw and not laying flat.
Align Edges: How to Install Baseboard | DIY PlaybookTo make the cut on the other 1/2 of the mitered corner simply change the 45 degree angle on the saw to the other side of saw (still 45 degrees) and make a cut. Once you put those two angles together they should fit perfectly into a 90 degree corner.

Rookie Tip: This is not hard but sometimes it takes a few cuts of trial and error to confirm that you have it down (it can feel like a bit of a brain puzzle sometimes). I would suggest making a few practice cuts on leftover/scrap trim so you can perfect the combo before doing it on your new baseboard or shoe.

Another Rookie Tip: I usually mark my baseboard for size and then draw the angle that I want to cut. This little sketch really helps when I take it to the saw becauseย I have a visualย reminder about which angle I need to cut.

3. Nail it to the wall

Before I nail the new baseboard to the wall, I lay it along the wall around the perimeter of the room and make sure it fits like a glove (or as close as possible) before nailing it to the wall.
Nail to the wall

When I feel like it’s perfect, it’s time to nail it to the wall using a nail gun.
Make it aligned: How to Install Baseboard | DIY Playbook

You’ll want to nail the baseboard on the top and bottom of the baseboard along the entire piece. I was a little too generous with the nail gun on this piece, but I guess it’s better to have a few too many nails than too few.

4. Repeat Steps #2 – #3 with the shoeRepeat with the shoe: How to Install Baseboard | DIY Playbook

Now that the baseboard is attached, it’s time to attach the shoe. Honestly you follow the exact same baseboard steps to attach the shoe. Getting the perfect mitered edges with the shoe alwaysย seems a little bit more confusing to me so I definitely take advantage of a few practice cuts before I attempt the “real” cut. But just like the baseboard, some of the shoe may just require a straight cut… which is by far the easiest!

4. Putty the Nail Holes

Putty the nail holes: How to Install Baseboard | DIY PlaybookHaving too many nail holes is not a huge problem, but it does make this step a little more time-consuming. Take the putty and fill in all of the nail holes on the baseboard and shoe. Once it has dried, you can lightly sand off the excess so it’s a smooth surface and ready for primer/paint.

5. Caulk

Caulk: How to Install Baseboard | DIY PlaybookIf you’re tackling white baseboard and trim, caulk is your BEST FRIEND because it can help mask some of your less than perfect cuts. I like to use bright white caulk (to match the bright white trim) and caulk that is specifically made for trimwork.

As you can see here the photo on the left is a straight cut that was cut just a hair short. But after caulking the edge, you can hardly see this tiny imperfection. This same idea goes for all of your corners of both the baseboard and the trim! <— caulk makes the finished project look a LOT more professional.ย 

You’ll also want to caulk the space in between the baseboard and the shoe (if there are any gaps or inconsistencies), where the shoe hits the floor, as well as the seam where the baseboard hits the wall.

6. Prep for Painting

Once the caulk is dried, it’s time to finish this gorgeous new baseboard with a few fresh coats of paint!
Prep for Paint: How to Install Baseboard | DIY PlaybookI typically tape everything around the trim (floor, walls, outlets, etc.) so that I don’t make a mess.
Paint: How to Install Baseboard | DIY PlaybookThe tape is especially important on the floor if you are not an experienced painter… no one wants bright white paint on their hardwoodย floors (or carpets!). #yikes

7. Prime + PaintPrime & Paint: How to Install Baseboard | DIY Playbook

Then it’s time to prime and paint. I typically put one coat of primer on the baseboard followed by a light sanding to remove anything left on the baseboard.
Paint: How to Install Baseboard | DIY PlaybookAfter that it’s time for a coat of bright white, semi-gloss paint. I used two coats of this paint just to make sure the baseboard was covered well, but you may only need one.

Rookie Tip: Most trim is painted with semi gloss because it’s the easiest to maintain/clean and it offers a good contrastย next to the wall, but honestly this is personal preference!
Semigloss makes it pop :How to Install Baseboard | DIY PlaybookMuch better right?! I love that after the caulk and paint the cuts looks perfect, even if they weren’t exactly perfect (our little secret).Make lines clean: How to Install Baseboard | DIY PlaybookAfter the trim is painted and dried you canย add tape the top of the baseboard and paint the wall that you previously patched. Once the wall is painted (if necessary) then your job is just about over!!

8. Remove Tape and Clean up

Is it already time to clean-up?!
Remove Tape and clean up: How to Install Baseboard | DIY PlaybookPeel up the tape, fold up the drop cloths, and clean up the area. If you’re left with any paint stains on the hardwood floor I like to use this Goof Off to clean up those little drips. You add a little to a cloth, wipe up the specific area, and it should wipe right up.

DISCLAIMER:ย Please test this product on your hardwood floors in a place that is not visible (maybe in a closet). Make sure it dries without impacting the finish of your floors before using it throughout the whole room. This product doesn’t have any impact on my floors, but that may not be the case with your floors depending on their finish. <– Better to be safe than sorry!! ย Clean Up: How to Install Baseboard | DIY Playbook

And just like that, your new baseboards are all done… and most importantly, you DIY-ed them! Replacing all of the baseboard inย your entire house may be a little overwhelming at first, but trying this out in one room will help you gain confidence in your skills and prove that you can do this, one step at a time.

My goal this summer is to replace a lot more old and grungy baseboard in other parts of our home. If you would have told me that I would be replacing baseboard throughout our house a year ago, I would have laughed at this absurd idea. But now that I’ve tackled a few smaller spaces, I feel more than capableย of replacing the baseboardย throughout the house. And now that I see what a difference this simple upgrade makes, I’m a lot more motivated to do so.

Bridget

Not sure how to get the old baseboard off and prep your walls for the installation of new baseboard? Check out this DIY Baseboard Tutorial!

 


The Year of Casey

Hey there!

Iโ€™m Casey Finn, the voice behind The DIY Playbook. I’m a Chicago gal teaching you how to design, DIY, and maintain your home…by yourself! Learn more about me right here.